Basic (Optimized) Configuration

The only file we’ll be modifying is your nginx.conf, which holds all your settings for nginx in different modules. You should be able to find nginx.conf in the/etc/nginx directory on your server. First, we’ll talk about some of the global settings, then go through each module in the file and talk about which settings will get you the best performance for a large number of clients, and why they’ll increase your performance. A completed config file can be found at the end of this post.

Top Level Configs

Nginx has a few top level configuration settings that sit outside the modules in your nginx.conf file.

user and pid should be set by default – we won’t modify this, since it won’t do anything for us

worker_processes defines the number of worker processes that nginx should use when serving your website. The optimal value depends on many factors including (but not limited to) the number of CPU cores, the number of hard drives that store data, and load pattern. When in doubt, setting it to the number of available CPU cores would be a good start (the value “auto” will try to autodetect it).

worker_rlimit_nofile changes the limit on the maximum number of open files for worker processes. If this isn’t set, your OS will limit. Chances are your OS and nginx can handle more than “ulimit -a” will report, so we’ll set this high so nginx will never have an issue with “too many open files”

Events Module

The events module contains all the settings for processing connections in nginx.

worker_connections sets the maximum number of simultaneous connections that can be opened by a worker process. Since we bumped up worker_rlimit_nofile, we can safely set this pretty high.

Keep in mind that the maximum number of clients is also limited by the number of socket connections available on your sytem (~64k), so setting this ridiculously high won’t benefit us.

multi_accept tells nginx to accept as many connections as possible after getting a notification about a new connection

use sets which polling method we should use for multiplexing clients on to threads. If you’re using Linux 2.6+, you should use epoll. If you’re using *BSD, you should use kqueue. Wanna know more about event polling?Let Wikipedia be your guide (warning, a neckbeard and an operating systems course might be needed to understand everything)

(it’s worth noting if you don’t which polling method nginx should use, it’ll chose the best one for your OS)

HTTP Module

The HTTP module controls all the core features of nginx’s http processing. Since there are quite a few settings in here, we’ll take this one in pieces. All these settings should be in the http module, even though it won’t be specifically noted as such in the snippets.

server_tokens doesn’t speed up our performance any, but it turns off nginx version numbers on error pages, which is a good idea for security.

sendfile enables the use of sendfile(). sendfile() copies data between the disk and a TCP socket (or any two file descriptors). Pre-sendfile, to transfer such data we would alloc a data buffer in the user space. We would then read() to copy the data from a file in to the buffer, and write() the content of the buffer to a network. sendfile() reads the data immediately from the disk into the OS cache. Because this copying is done within the kernel, sendfile() is more efficient than the combination of read() and write() and the context switching/cache trashing that comes along with it (read more about sendfile)

tcp_nodelay tells nginx not to buffer data and send data in small, short bursts – it should only be set for applications that send frequent small bursts of information without getting an immediate response, where timely delivery of data is required

access_log sets whether or not nginx will store access logs. Turning this off increases speed by reducing disk IO (aka, YOLO)

error_log tells nginx it should only log critical errors

keepalive_timeout assigns the timeout for keep-alive connections with the client. The server will close connections after this time. We’ll set it low to keep our workers from being busy for too long.

client_header_timeout and client_body_timeout sets the timeout for the request header and request body (respectively). We’ll set this low too.

send_timeout specifies the response timeout to the client. This timeout does not apply to the entire transfer, but between two subsequent client-read operations. If the client has not read any data for this amount of time, then nginx shuts down the connection.

limit_conn_zone sets parameters for a shared memory zone that will keep states for various keys (such as current number of connections). 5m is 5 megabytes, and should be large enough to store (32k * 5) 32-byte states or (16k * 5) 64-byte states.

limit_conn sets the maximum allowed number of connections for a given key value. The key is addr, and our value is 100, so we’ll only allow 100 concurrent connections per IP address.

include is just a directive to include the contents of another file in the current file. Here, we use it to load in a list of MIME types to be used later.

default_type sets the default MIME-type to be used for files

charset sets the default charset to be included in our header

gzip tells nginx to gzip the data we’re sending. This will reduce the amount of data we need to send.gzip_disable disables gzip for specific clients. We set it to be IE6 or less for compadibility issues.

gzip_static tells nginx to look for the pre-gzip’d asset with the same name before gzipping the asset itself. This is requires you to pre-zip your files (it’s commented out for this example), but allows you to use the highest compression possible and nginx no longer has to zip those files (read more about gzip_statichere)

gzip_proxied allows or disallows compression of a response based on the request/response. We’ll set it to any, so we gzip all requests.

gzip_min_length sets the minimum number of bytes necessary for us to gzip data. If a request is under 1000 bytes, we won’t bother gzipping it, since gzipping does slow down the overall process of handling a request.

gzip_comp_level sets the compression level on our data. These levesls can be anywhere from 1-9, 9 being the slowest but most compressed. We’ll set it to 4, which is a good middle ground.

gzip_types sets the type of data to gzip. There are some above, but you can add more.

open_file_cache_min_uses defines the minimum use number of a file within the time specified in the directive parameter inactive in open_file_cache

open_file_cache_errors specifies whether or not to cache errors when searching for a file

Include is again used to add some files to our config. We’re including our server modules, defined in a different file. If your server modules aren’t at these locations, you should modify this line to point at the correct location.

The full config file

After editing your config, make sure to restart nginx in order to have it use our new configuration file

sudo service nginx restart

Takeaway

There we go! Your web server is now ready to do battle with the army of visitors that previously plagued you. This is by no means the only way you can go about speeding up your website. I’ll be writing more posts that explain other ways to speed up your website soon.